{"product_id":"wall-eave-mount-for-all-starlink-models-750mm-long","title":"Starlink Wall \u0026 Eave Mount for all Starlink Models - 750mm long","description":"\u003ch2 data-start=\"107\" data-end=\"391\"\u003eThe Starlink Wall \u0026amp; Eave Mount is a fixed structural mounting solution designed for permanent installation on building walls or eaves\u003c\/h2\u003e\n\u003cp data-start=\"107\" data-end=\"391\"\u003eIt provides a stable, elevated mounting position for the Starlink Gen 3 (V4, Standard 4) \u0026amp; Starlink Mini terminals where roof mounting is not preferred or practical.\u003c\/p\u003e\n\u003cp\u003eManufactured in Australia for Australian \u0026amp; New Zealand conditions, the system includes a pole adapter to suit the selected Starlink model. The adapter incorporates a fixed 20-degree mast angle in line with Starlink installation guidance, supporting correct dish orientation and long-term mechanical stability.\u003c\/p\u003e\n\u003cp\u003eChoose between a\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003ebracket arm length of 350mm (small) or 750mm (large)\u003c\/strong\u003e. The larger arm is intended for homes with longer eaves (particularly in tropical areas) that cater for larger rainfall. The spigot (pole) is roughly at 320mm \/ 720mm from the base of the arm. The Starlink should be oriented towards te South \/ South East sky. \u003c\/p\u003e\n\u003cp\u003e💡\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eTIP\u003c\/strong\u003e: If mounting on the northern side of your structure, ensure you check clearances as your Starlink dish will be tilted back towards your wall \/ gutters to look at the southern sky.  \u003cbr\u003e\u003cbr\u003ePlease note : Our kits do not come with a Starlink \u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003eKit Inclusions: \u003c\/strong\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 x Starlink Pole Adator \u0026amp; Grub Screws - (Choose Starlink Model) \u003c\/li\u003e\n\u003cli\u003e2 x Aluminium Wall Mount Spacers\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003e1 x Aluminium Wall Mount Bracket\/Arm (Choose Length, 350mm or 750mm). \n\u003cul\u003e\n\u003cli\u003eFor 750mm mount, requires 720mm clearance from wall for spigot. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003e1 x 400mm\u003cspan\u003e \u003c\/span\u003eAluminium Spigot \u003c\/li\u003e\n\u003cli\u003eGeneric Fastener Pack (please check suitability for your specific install)\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003ePlease note, our kits come as raw aluminium (by design) - made proudly by Australian metalworkers in regional Victoria.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNote\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e: Starlink Mini Pole Adaptor is ABS Plastic with 6 tension points.  Starlink Gen 3 (V4) adaptor is powder coated aluminium. \u003cbr\u003e\u003c\/p\u003e\n\u003ch3 data-start=\"877\" data-end=\"896\"\u003e\u003cstrong data-start=\"880\" data-end=\"896\"\u003eKey Features\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp data-start=\"898\" data-end=\"1028\"\u003e✅\u003cspan\u003e \u003c\/span\u003e\u003cstrong data-start=\"901\" data-end=\"936\"\u003eWall \u0026amp; Eave Structural Mounting\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— Designed for secure attachment to walls or eaves on residential and commercial buildings.\u003c\/p\u003e\n\u003cp data-start=\"1030\" data-end=\"1163\"\u003e✅\u003cspan\u003e \u003c\/span\u003e\u003cstrong data-start=\"1033\" data-end=\"1073\"\u003eAluminium Construction\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— Corrosion-resistant finish suitable for coastal, rural, and high-exposure environments.\u003c\/p\u003e\n\u003cp data-start=\"1165\" data-end=\"1272\"\u003e\u003cstrong data-start=\"1168\" data-end=\"1203\"\u003e✅ Integrated 20-Degree Mast Angle\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— Aligns with Starlink Gen 3 (V4) recommended installation geometry.\u003c\/p\u003e\n\u003cp data-start=\"1274\" data-end=\"1395\"\u003e\u003cstrong data-start=\"1277\" data-end=\"1319\"\u003e✅ Pole Adapter Included\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— Rigid interface engineered for repeated installation without deformation.\u003c\/p\u003e\n\u003cp data-start=\"1397\" data-end=\"1520\"\u003e\u003cstrong data-start=\"1400\" data-end=\"1442\"\u003e✅ Service-Accessible Installation Height\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— Allows access via ladder for maintenance or terminal removal when required.\u003cstrong data-start=\"1530\" data-end=\"1548\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch3 data-start=\"1965\" data-end=\"1993\"\u003e\u003cstrong data-start=\"1968\" data-end=\"1993\"\u003eInstallation Instructions\u003c\/strong\u003e\u003c\/h3\u003e\n\u003col\u003e\n\u003cli data-start=\"1998\" data-end=\"2078\"\u003e\n\u003cp\u003eIdentify a structurally sound wall or eave location with clear sky visibility of the southern sky. (If in the southern hemisphere). TIP : If you are planning to mount on the nothern side of your building, ensure the spigot's height allows the Starlink to tilt towards the southern sky and not be obstructed by the roof structure. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli data-start=\"2082\" data-end=\"2151\"\u003e\n\u003cp\u003eMark fixing points aligned with underlying timber, concrete or steel support structure.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli data-start=\"2155\" data-end=\"2210\"\u003e\n\u003cp\u003ePre-drill fixing holes as required for the substrate. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli data-start=\"2214\" data-end=\"2283\"\u003e\n\u003cp\u003eApply appropriate exterior-grade sealant to all penetration points.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli data-start=\"2287\" data-end=\"2355\"\u003e\n\u003cp\u003eSecure the mount base onto the penetration points using supplied hardware (or your own), ensure suitability to your specific substrate. If using concrete, wall plugs are recommended (not supplied). The cylinder shaped washes are used to offset the base of the mount against the wall.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eInsert the vertical spigot through the center of the mounting arm, fastening the spigot to the mounting arm using the supplied hex bolt and nut. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli data-start=\"2440\" data-end=\"2504\"\u003e\n\u003cp\u003eConfirm 90 degree alignment and mechanical rigidity before mounting\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePrepare the Starlink for final mounting position - remove the ground kickstand from the Gen 3 (V4) or Starlink Mini - you can see how to do this\u003cspan\u003e \u003c\/span\u003e\u003ca href=\"https:\/\/www.youtube.com\/shorts\/k3bLEMf6GnQ\" title=\"Remove the Starlink Gen 3 (V4) Kickstand\" rel=\"noopener\" target=\"_blank\" aria-label=\"Visit a webpage about Remove the Starlink Gen 3 (V4) Kickstand\"\u003ehere.\u003c\/a\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eInsert the Starlink cable data cable into the Starlink, you have two options for cable run, (a) you can pass the cable through the pole adapter and into the spigot, securing the cable along the bottom of the arm with cable ties and then back into your home\/structure. or (b) you can exit the cable near the top of the pole adapter, running the cable down the adapter , across the top of the mounting arm and back into your home \/ structure. Ensure in both cable runs you remove excess slack and secure the cable to the mount. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eInsert the SPACETEK pole adaptor for the Starlink into the same position the kickstand was occupying, ensuring it clicks into place and does not come out when agitated. It should be firmly in place. Ensure the cable is running smoothly through the adaptor. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eSlide the SPACETEK pole adaptor over the end of the mounted spigot, using the grub screws and included allen key to tighten \/ create tension around the pole to secure the adaptor. Note - that the Starlink dish should be facing south in preparation for signal calibration, you do not need to full tighten the grub screws as yet. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eOnce the cable run is complete within the home\/structure and reaches the router. Turn everything on and commence Starlink calibration in your Starlink App as per the instructions in Starlink documentation. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eIf required - adjust the angle of the dish by turning the dish on the spigot and adjusting the grub screws for micro-level adjustments using the Starlink app calibration process as a guide.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eOnce fully aligned , tighten the grub screws with the included allen key. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3 data-start=\"2511\" data-end=\"2533\"\u003e\u003cstrong data-start=\"2514\" data-end=\"2533\"\u003eImportant Notes\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp data-start=\"2535\" data-end=\"2857\"\u003e⚠️\u003cspan\u003e \u003c\/span\u003e\u003cem data-start=\"2538\" data-end=\"2609\"\u003e\u003cstrong data-start=\"2539\" data-end=\"2608\"\u003eNot suitable for ground, freestanding, or portable installations.\u003c\/strong\u003e\u003c\/em\u003e\u003cbr data-start=\"2609\" data-end=\"2612\"\u003e⚠️\u003cspan\u003e \u003c\/span\u003e\u003cem data-start=\"2615\" data-end=\"2691\"\u003e\u003cstrong data-start=\"2616\" data-end=\"2690\"\u003eAll roof or wall penetrations must be sealed to prevent water ingress.\u003c\/strong\u003e\u003c\/em\u003e\u003cbr data-start=\"2691\" data-end=\"2694\"\u003e⚠️\u003cspan\u003e \u003c\/span\u003e\u003cem data-start=\"2697\" data-end=\"2770\"\u003e\u003cstrong data-start=\"2698\" data-end=\"2769\"\u003eUse only substrate-rated fasteners and fix into structural members.\u003c\/strong\u003e\u003c\/em\u003e\u003cbr data-start=\"2770\" data-end=\"2773\"\u003e⚠️\u003cspan\u003e \u003c\/span\u003e\u003cem data-start=\"2776\" data-end=\"2857\"\u003e\u003cstrong data-start=\"2777\" data-end=\"2856\"\u003eProfessional installation is recommended\u003c\/strong\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003ch2 data-start=\"2864\" data-end=\"2886\"\u003e\u003cstrong data-start=\"2867\" data-end=\"2886\"\u003eIdeal Use Cases\u003c\/strong\u003e\u003c\/h2\u003e\n\u003cp data-start=\"2888\" data-end=\"3060\"\u003e✅ Residential wall installations\u003cbr data-start=\"2920\" data-end=\"2923\"\u003e✅ Eave-mounted Starlink systems\u003cbr data-start=\"2954\" data-end=\"2957\"\u003e✅ Rural and regional properties\u003cbr data-start=\"2988\" data-end=\"2991\"\u003e✅ Fixed building installations where roof mounting is not preferred\u003c\/p\u003e","brand":"PC MART","offers":[{"title":"Default Title","offer_id":49882086342899,"sku":null,"price":329.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0654\/9674\/4179\/files\/starlink-wall-eave-mount-for-all-models-750mm-long-849.webp?v=1783475653","url":"https:\/\/pcmart.net.au\/products\/wall-eave-mount-for-all-starlink-models-750mm-long","provider":"PC MART","version":"1.0","type":"link"}